Lenco Trim Tab Kit 12V 12×12 – LEN15007 is an electric standard-mount trim tab system designed to help improve a boat’s running attitude, balance, and handling on the water. By adjusting the position of the trim tab blades at the transom, the system allows the operator to compensate for uneven passenger or equipment loads and changing sea or wind conditions. Correct trim adjustment can help reduce bow rise, correct port-to-starboard listing, and support a more level, comfortable ride.

This Lenco trim tab kit uses two fast-response 12V electric actuators to move the stainless steel blades. The direct electric design does not require a hydraulic pump, reservoir, or hydraulic hoses. Each blade measures 12 × 12 inches, approximately 30 × 30 cm, providing a practical trim surface for compatible recreational and working boats. Lenco identifies this standard-mount 12V configuration for boats approximately 17–30 feet, or 5.2–9.2 metres, depending on hull design, weight distribution, available transom space, and operating requirements.

The kit contains two 12-gauge 304 stainless steel trim tab blades, two electric actuators with 6-foot (1.8-metre) leads and Deutsch connectors, two 20-foot (6.1-metre) actuator extension wiring harnesses, upper mounting brackets with gland seals, and lower mounting brackets. These corrosion-resistant marine components are intended for installation on the boat’s transom. The standard mounting arrangement makes the system suitable for boats with enough clear transom area for the blades, actuators, and their required movement. The official Lenco listing identifies the 12 × 12-inch standard-mount 12V version as part number 15007-101.

These Lenco electric trim tabs are useful when a boat needs more control over fore-and-aft trim or side-to-side balance. Independent movement of the port and starboard tabs allows adjustment for uneven loading, while operating both tabs can help manage the boat’s bow attitude. Results depend on the hull, speed, loading, and conditions, so the tabs should be adjusted gradually while monitoring the boat’s response.

A compatible 12V trim tab control switch is not included and must be selected separately. Buyers should confirm the boat’s electrical system voltage, transom dimensions, mounting clearance, and suitable control before ordering. Installation should follow the manufacturer’s current instructions, with careful attention to actuator position, blade alignment, wiring connections, and sealing of transom penetrations. The stated packaged dimensions are approximately 36 cm long, 34 cm wide, and 14 cm high, with a packaged weight of about 8.6 kg.

Key Features:

• Lenco Trim Tab Kit 12V 12×12 – LEN15007 provides an electric trim-control solution for compatible boats requiring improved running balance and adjustable bow attitude.
• Two 12 × 12-inch trim tab blades provide approximately 30 × 30 cm of trim surface on each side.
• Two 12V electric actuators deliver direct blade movement without a separate hydraulic power unit, fluid reservoir, or hydraulic hoses.
• The kit uses durable 12-gauge 304 stainless steel blades for marine transom installation.
• Independent port and starboard adjustment helps compensate for uneven passengers, fuel, equipment, or other onboard loads.
• Supplied with two actuators featuring 6-foot (1.8-metre) leads and Deutsch electrical connectors.
• Includes two 20-foot (6.1-metre) actuator extension wiring harnesses for connection within the boat’s electrical installation.
• Upper mounting brackets with gland seals and lower mounting brackets are included.
• The standard-mount design is intended for transoms with adequate mounting area and actuator clearance.
• Suitable boat-length guidance is approximately 17–30 feet, or 5.2–9.2 metres, subject to the vessel’s hull and installation requirements.
• A compatible 12V power switch or trim tab control is required separately and is not included with this kit.
• Brand: Lenco; product reference/SKU: LEN15007; corresponding current Lenco variant: 15007-101.

Applications / Suitable For:

• Lenco Trim Tab Kit 12V 12×12 – LEN15007 is suitable for compatible 12V boats that need adjustable control of running trim and side-to-side balance.
• Recreational powerboats, fishing boats, centre consoles, cruisers and similar planing vessels within the recommended size range.
• Boats affected by uneven passenger seating, changing fuel levels, fishing equipment, batteries or other variable onboard loads.
• Applications where the operator needs to correct a port or starboard list while the boat is underway.
• Boats requiring better management of bow rise and running attitude during changing load, speed, or water conditions.
• New trim tab installations or replacement projects where a 12 × 12-inch Lenco standard-mount system matches the existing transom layout.
• Marine installations with sufficient transom height and clearance for both blades and actuator movement.

FAQs:

Q: What is the Lenco Trim Tab Kit 12V 12×12 – LEN15007 used for?
A: It is used to adjust a boat’s running attitude, correct uneven side-to-side loading, and help control bow position while underway.

Q: What boat size is this Lenco trim tab kit suitable for?
A: It is generally recommended for compatible boats approximately 17–30 feet (5.2–9.2 metres), but hull type, weight, and transom space must also be checked.

Q: Does the kit include a control switch?
A: No. A compatible 12V Lenco trim tab switch or control must be purchased separately.

Q: What components are supplied in the kit?
A: It includes two 12 × 12-inch stainless steel blades, two 12V actuators, extension wiring harnesses, upper brackets with gland seals, and lower mounting brackets.